Hi, remote access is not working for me in build 54:
I have rebooted the router aswell, and both the http and ssh services are not listed as listening ports (1726 & 1727).
Transmission works fine on port 1728 as displayed in the ssh window.
(The ssh and http session is within the local network, using iphone to test remote connections).
What am I doing wrong? Or is this a bug?
Thankyou!
You won't see them as listeners because Tomato handles it via port forwards.
What do you see in iptables?
Rodney
My Tomato utilities site: http://multics.minidns.net/blog/articles/tomato_utilities
Is this what your looking for?
root@NAS:/tmp/home/root# iptables -L
Chain INPUT (policy DROP)
target prot opt source destination
DROP all -- anywhere anywhere state INVALID
ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED
ACCEPT all -- anywhere anywhere
ACCEPT all -- anywhere anywhere
ACCEPT icmp -- anywhere anywhere limit: avg 1/sec burst 5
ACCEPT udp -- anywhere anywhere udp dpts:33434:33534 limit: avg 5/sec burst 5
ACCEPT tcp -- anywhere NAS tcp dpt:ssh
ACCEPT igmp -- anywhere anywhere
Chain FORWARD (policy ACCEPT)
target prot opt source destination
TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
root@NAS:/tmp/home/root#
I dont think it worked then though the gui… Ill try manually forwarding the ports.
What is the output of this?
/usr/sbin/iptables -t nat -n -L WANPREROUTING
Rodney
My Tomato utilities site: http://multics.minidns.net/blog/articles/tomato_utilities
Sorry for the double post but I really dont know much about iptables (or complex networking for that matter), so if you would like me to manually port forward the ports then could you kindly post the required commands? :)
Thanks for your help so far!
Wow - something has definitely gone wrong.
I wouldn't advise manually forwarding because it's going to mask what is really happening (and cause later breakage).
Unfortunately I'm not quite sure where to look on this one because I haven't seen it before. Can you do a clean reboot, wait for it to settle, then paste the _complete_ messages/system log?
Rodney
My Tomato utilities site: http://multics.minidns.net/blog/articles/tomato_utilities
Status > Logs (from web gui):
Jan 1 08:00:45 NAS syslog.info syslogd started: BusyBox v1.17.4
Jan 1 08:00:45 NAS user.notice kernel: klogd started: BusyBox v1.17.4 (2010-11-30 14:25:45 EST)
Jan 1 08:00:45 NAS user.notice kernel: Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #7 Tue Nov 30 14:44:12 EST 2010
Jan 1 08:00:45 NAS user.warn kernel: CPU revision is: 00019740
Jan 1 08:00:45 NAS user.warn kernel: Determined physical RAM map:
Jan 1 08:00:45 NAS user.warn kernel: memory: 04000000 @ 00000000 (usable)
Jan 1 08:00:45 NAS user.debug kernel: On node 0 totalpages: 16384
Jan 1 08:00:45 NAS user.debug kernel: Normal zone: 128 pages used for memmap
Jan 1 08:00:45 NAS user.debug kernel: Normal zone: 0 pages reserved
Jan 1 08:00:45 NAS user.debug kernel: Normal zone: 16256 pages, LIFO batch:3
Jan 1 08:00:45 NAS user.warn kernel: Built 1 zonelists. Total pages: 16256
Jan 1 08:00:45 NAS user.notice kernel: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Jan 1 08:00:45 NAS user.warn kernel: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Jan 1 08:00:45 NAS user.warn kernel: Primary data cache 32kB, 4-way, linesize 32 bytes.
Jan 1 08:00:45 NAS user.info kernel: Synthesized TLB refill handler (20 instructions).
Jan 1 08:00:45 NAS user.info kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan 1 08:00:45 NAS user.info kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan 1 08:00:45 NAS user.info kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan 1 08:00:45 NAS user.warn kernel: PID hash table entries: 256 (order: 8, 1024 bytes)
Jan 1 08:00:45 NAS user.warn kernel: CPU: BCM4716 rev 1 pkg 10 at 480 MHz
Jan 1 08:00:45 NAS user.warn kernel: Using 240.000 MHz high precision timer.
Jan 1 08:00:45 NAS user.info kernel: console [ttyS0] enabled
Jan 1 08:00:45 NAS user.warn kernel: Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 08:00:45 NAS user.warn kernel: Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 08:00:45 NAS user.info kernel: Memory: 61804k/65536k available (2333k kernel code, 3668k reserved, 476k data, 112k init, 0k highmem)
Jan 1 08:00:45 NAS user.info kernel: SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Jan 1 08:00:45 NAS user.debug kernel: Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Jan 1 08:00:45 NAS user.warn kernel: Mount-cache hash table entries: 512
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 16
Jan 1 08:00:45 NAS user.warn kernel: PCI: Using membase 8000000
Jan 1 08:00:45 NAS user.warn kernel: PCI: Initializing host
Jan 1 08:00:45 NAS user.warn kernel: PCI: Reset RC
Jan 1 08:00:45 NAS user.warn kernel: PCI: Fixing up bus 0
Jan 1 08:00:45 NAS user.warn kernel: PCI: Fixing up bridge
Jan 1 08:00:45 NAS user.debug kernel: PCI: Setting latency timer of device 0000:01:00.0 to 64
Jan 1 08:00:45 NAS user.warn kernel: PCI: Fixing up bridge
Jan 1 08:00:45 NAS user.debug kernel: PCI: Setting latency timer of device 0000:01:00.1 to 64
Jan 1 08:00:45 NAS user.warn kernel: PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
Jan 1 08:00:45 NAS user.warn kernel: PCI: Fixing up bus 1
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 2
Jan 1 08:00:45 NAS user.info kernel: Time: MIPS clocksource has been installed.
Jan 1 08:00:45 NAS user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 08:00:45 NAS user.warn kernel: TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 08:00:45 NAS user.warn kernel: TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 08:00:45 NAS user.info kernel: TCP: Hash tables configured (established 2048 bind 2048)
Jan 1 08:00:45 NAS user.info kernel: TCP reno registered
Jan 1 08:00:45 NAS user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
Jan 1 08:00:45 NAS user.info kernel: io scheduler noop registered (default)
Jan 1 08:00:45 NAS user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
Jan 1 08:00:45 NAS user.info kernel: N_HDLC line discipline registered.
Jan 1 08:00:45 NAS user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Jan 1 08:00:45 NAS user.info kernel: serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
Jan 1 08:00:45 NAS user.info kernel: PPP generic driver version 2.4.2
Jan 1 08:00:45 NAS user.info kernel: MPPE/MPPC encryption/compression module registered
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 24
Jan 1 08:00:45 NAS user.info kernel: PPPoL2TP kernel driver, V0.17
Jan 1 08:00:45 NAS user.info kernel: PPTP driver version 0.8.5
Jan 1 08:00:45 NAS user.info kernel: Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Jan 1 08:00:45 NAS user.debug kernel: Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Jan 1 08:00:45 NAS user.debug kernel: Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Jan 1 08:00:45 NAS user.debug kernel: Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Jan 1 08:00:45 NAS user.warn kernel: Amd/Fujitsu Extended Query Table at 0x0040
Jan 1 08:00:45 NAS user.notice kernel: number of CFI chips: 1
Jan 1 08:00:45 NAS user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan 1 08:00:45 NAS user.notice kernel: Flash device: 0x800000 at 0x1c000000
Jan 1 08:00:45 NAS user.notice kernel: Creating 5 MTD partitions on "Physically mapped flash":
Jan 1 08:00:45 NAS user.notice kernel: 0x00000000-0x00040000 : "pmon"
Jan 1 08:00:45 NAS user.notice kernel: 0x00040000-0x007f0000 : "linux"
Jan 1 08:00:45 NAS user.notice kernel: 0x00131400-0x00690000 : "rootfs"
Jan 1 08:00:45 NAS user.notice kernel: 0x00690000-0x007f0000 : "jffs2"
Jan 1 08:00:45 NAS user.notice kernel: 0x007f0000-0x00800000 : "nvram"
Jan 1 08:00:45 NAS user.warn kernel: Found a 0MB serial flash
Jan 1 08:00:45 NAS user.err kernel: sflash: found no supported devices
Jan 1 08:00:45 NAS user.warn kernel: u32 classifier
Jan 1 08:00:45 NAS user.warn kernel: OLD policer on
Jan 1 08:00:45 NAS user.warn kernel: Netfilter messages via NETLINK v0.30.
Jan 1 08:00:45 NAS user.warn kernel: nf_conntrack version 0.5.0 (512 buckets, 4096 max)
Jan 1 08:00:45 NAS user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 08:00:45 NAS user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Nov 30 2010 14:43:01]
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 1
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 10
Jan 1 08:00:45 NAS user.warn kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 08:00:45 NAS user.info kernel: NET: Registered protocol family 17
Jan 1 08:00:45 NAS user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Jan 1 08:00:45 NAS user.info kernel: All bugs added by David S. Miller <davem@redhat.com>
Jan 1 08:00:45 NAS user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 08:00:45 NAS user.info kernel: Freeing unused kernel memory: 112k freed
Jan 1 08:00:45 NAS user.warn kernel: Warning: unable to open an initial console.
Jan 1 08:00:45 NAS user.warn kernel: et: module license 'Proprietary' taints kernel.
Jan 1 08:00:45 NAS user.debug kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
Jan 1 08:00:46 NAS user.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.147.0
Jan 1 08:00:46 NAS user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 08:00:46 NAS user.warn kernel: eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.147.0
Jan 1 08:00:46 NAS user.warn kernel: PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
Jan 1 08:00:46 NAS user.debug kernel: PCI: Setting latency timer of device 0000:01:01.0 to 64
Jan 1 08:00:46 NAS user.warn kernel: eth2: Broadcom BCM4322 802.11 Wireless Controller 5.10.147.0
Jan 1 08:00:46 NAS user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 08:00:46 NAS user.info kernel: usbcore: registered new interface driver usbfs
Jan 1 08:00:46 NAS user.info kernel: usbcore: registered new interface driver hub
Jan 1 08:00:46 NAS user.info kernel: usbcore: registered new device driver usb
Jan 1 08:00:46 NAS user.notice kernel: SCSI subsystem initialized
Jan 1 08:00:46 NAS user.info kernel: Initializing USB Mass Storage driver...
Jan 1 08:00:46 NAS user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 08:00:46 NAS user.info kernel: USB Mass Storage support registered.
Jan 1 08:00:46 NAS user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 08:00:46 NAS user.debug kernel: PCI: Setting latency timer of device 0000:00:04.1 to 64
Jan 1 08:00:46 NAS user.info kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
Jan 1 08:00:46 NAS user.info kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
Jan 1 08:00:46 NAS user.info kernel: ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
Jan 1 08:00:46 NAS user.info kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
Jan 1 08:00:46 NAS user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 08:00:46 NAS user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 08:00:46 NAS user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 08:00:46 NAS user.debug hotplug[385]: Attached USB device 1-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/2/206]
Jan 1 08:00:46 NAS user.info kernel: usbcore: registered new interface driver usblp
Jan 1 08:00:46 NAS user.info kernel: usblp: USB Printer Device Class driver
Jan 1 08:00:46 NAS user.debug kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 08:00:46 NAS user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 08:00:46 NAS user.info kernel: vlan1: dev_set_allmulti(master, 1)
Jan 1 08:00:46 NAS user.info kernel: vlan1: dev_set_promiscuity(master, 1)
Jan 1 08:00:46 NAS user.info kernel: device eth0 entered promiscuous mode
Jan 1 08:00:46 NAS user.info kernel: device vlan1 entered promiscuous mode
Jan 1 08:00:46 NAS user.info kernel: device eth1 entered promiscuous mode
Jan 1 08:00:47 NAS user.info kernel: device eth2 entered promiscuous mode
Jan 1 08:00:47 NAS user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 08:00:47 NAS user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 08:00:47 NAS user.info kernel: vlan2: dev_set_promiscuity(master, 1)
Jan 1 08:00:47 NAS user.info kernel: device vlan2 entered promiscuous mode
Jan 1 08:00:47 NAS user.info kernel: br0: port 4(vlan2) entering forwarding state
Jan 1 08:00:47 NAS user.info kernel: br0: port 3(eth2) entering forwarding state
Jan 1 08:00:47 NAS user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 08:00:47 NAS user.info kernel: br0: port 1(vlan1) entering forwarding state
Jan 1 08:00:47 NAS user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from vlan interface
Jan 1 08:00:47 NAS user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from master interface
Jan 1 08:00:47 NAS user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from vlan interface
Jan 1 08:00:47 NAS user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from master interface
Jan 1 08:00:47 NAS user.info kernel: br0: port 4(vlan2) entering disabled state
Jan 1 08:00:47 NAS user.warn kernel: vlan2: Setting MAC address to 68 7f 74 9f 85 d7.
Jan 1 08:00:47 NAS user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 08:00:47 NAS user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 08:00:47 NAS user.info kernel: br0: port 4(vlan2) entering forwarding state
Jan 1 08:00:48 NAS authpriv.info dropbear[543]: Running in background
Jan 1 08:00:50 NAS daemon.err nmbd[624]: Samba server NAS is now a domain master browser for workgroup WORKGROUP on subnet UNICAST_SUBNET
Jan 1 08:00:50 NAS user.info init[1]: Linksys WRT610N v2: Tomato 1.28.9054 MIPSR2-beta K26 USB Ext
Jan 4 14:51:36 NAS daemon.err nmbd[624]: Samba server NAS is now a domain master browser for workgroup WORKGROUP on subnet 192.168.1.2
Jan 4 14:51:38 NAS authpriv.info dropbear[804]: Child connection from ::ffff:192.168.1.6:49589
Jan 4 14:51:39 NAS cron.err crond[572]: time disparity of 21568730 minutes detected
Jan 4 14:51:43 NAS authpriv.notice dropbear[804]: password auth succeeded for 'root' from ::ffff:192.168.1.6:49589
Jan 4 14:51:51 NAS daemon.err nmbd[624]: Samba name server NAS is now a local master browser for workgroup WORKGROUP on subnet 192.168.1.2
Jan 4 14:53:23 NAS authpriv.info dropbear[804]: exit after auth (root): Exited normally
Jan 4 14:54:43 NAS authpriv.info dropbear[935]: Child connection from ::ffff:192.168.1.6:49593
Jan 4 14:54:47 NAS authpriv.notice dropbear[935]: password auth succeeded for 'root' from ::ffff:192.168.1.6:49593
Jan 4 14:55:45 NAS user.warn rstats[596]: Problem loading /mnt/Other/BanMon/tomato_rstats_687f749f85d6.gz. Still trying...
dmesg command though ssh:
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #7 Tue Nov 30 14:44:12 EST 2010
CPU revision is: 00019740
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 pkg 10 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61804k/65536k available (2333k kernel code, 3668k reserved, 476k data, 112k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.5
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1c000000
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x007f0000 : "linux"
0x00131400-0x00690000 : "rootfs"
0x00690000-0x007f0000 : "jffs2"
0x007f0000-0x00800000 : "nvram"
Found a 0MB serial flash
sflash: found no supported devices
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
net/ipv4/netfilter/tomato_ct.c [Nov 30 2010 14:43:01]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 112k freed
Warning: unable to open an initial console.
et: module license 'Proprietary' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.147.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.147.0
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:01.0 to 64
eth2: Broadcom BCM4322 802.11 Wireless Controller 5.10.147.0
Algorithmics/MIPS FPU Emulator v1.5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
usblp: USB Printer Device Class driver
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: dev_set_allmulti(master, 1)
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
vlan2: add 33:33:00:00:00:01 mcast address to master interface
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
vlan2: dev_set_promiscuity(master, 1)
device vlan2 entered promiscuous mode
br0: port 4(vlan2) entering forwarding state
br0: port 3(eth2) entering forwarding state
br0: port 2(eth1) entering forwarding state
br0: port 1(vlan1) entering forwarding state
vlan2: del 01:00:5e:00:00:01 mcast address from vlan interface
vlan2: del 01:00:5e:00:00:01 mcast address from master interface
vlan2: del 33:33:00:00:00:01 mcast address from vlan interface
vlan2: del 33:33:00:00:00:01 mcast address from master interface
br0: port 4(vlan2) entering disabled state
vlan2: Setting MAC address to 68 7f 74 9f 85 d7.
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
vlan2: add 33:33:00:00:00:01 mcast address to master interface
br0: port 4(vlan2) entering forwarding state
Gah - was hoping for some sort of obvious iptables problem (missing kernel module load or somesuch). We need teddy_bear's help with this.
Rodney
My Tomato utilities site: http://multics.minidns.net/blog/articles/tomato_utilities
